Electrical

Weighing just half a kilo and measuring 45cm by 15cm by 2cm, this 12 volt, 1.5 watt solar trickle charger provides longer battery life for infrequently used boats and vehicles. It comes with 2.7 metres of cable and a simple connection via either a 12V cigarette plug or battery clips. Flashing blue LED denotes charging while in-built blocking diode protects against reverse discharge. Amorphous solar cells use the sun's power to maintain the battery in peak condition, even in low light (cloudy) conditions.

The BLA Marine Performance DC DC Lithium Battery Charger is ideal for charging house and trolling motor lithium batteries whilst underway. The charger is ideally suited to the rigors of on board applications with each unit in a robust alloy housing, which is shockproof and water/ dust proof to IP65. It is configured to voltages for use with most lithium batteries (refer to batteries charge requirements), and utilises an ignition wire for activation for charging from the start battery. This ignition wire makes it suitable for use with wet, AGM or lithium start batteries. The charger has battery safety at mind with mulit-stage charging and features over voltage, over temperature, over current and short circuit protection. Dimensions are 200mm X 78mm X 33mm. Further Specs are in one of the photos so scroll through.

BLA Marine Performance IP 67 rated lithium chargers are a purpose built device specifically designed to match the BLA Marine Performance Lithium batteries charge profile. These chargers feature horizontal or vertical mounting holes for permanent installation on your boat. They are available in 12V, 24V & 36V models with 20 amp hour charging capacity. Complete with an easy to read LED display and battery ‘Wake-Up’ feature the BLA Marine Performance lithium charger is a must for anyone looking to easily maintain their BLA Marine Performance battery. Dimensions are 35cm by 25cm by 18cm. Further specs are in the last photo.

BLA Marine Performance IP 67 rated lithium chargers are a purpose built device specifically designed to match the BLA Marine Performance Lithium batteries charge profile. These chargers feature horizontal or vertical mounting holes for permanent installation on your boat. They are available in 12V, 24V & 36V models with 20 amp hour charging capacity. Complete with an easy to read LED display and battery ‘Wake-Up’ feature the BLA Marine Performance lithium charger is a must for anyone looking to easily maintain their BLA Marine Performance battery. Dimensions are 35cm by 25cm by 18cm. Further specs are in the last photo.

BLA Marine Performance IP 67 rated lithium chargers are a purpose built device specifically designed to match the BLA Marine Performance Lithium batteries charge profile. These chargers feature horizontal or vertical mounting holes for permanent installation on your boat. They are available in 12V, 24V & 36V models with 20 amp hour charging capacity. Complete with an easy to read LED display and battery ‘Wake-Up’ feature the BLA Marine Performance lithium charger is a must for anyone looking to easily maintain their BLA Marine Performance battery. Dimensions are 35cm by 25cm by 18cm. Further specs are in the last photo.

For use with lithium batteries between 9 volt and 60 volt, the X Series Battery Monitor Display gives real-time readings from BLA Marine Performance X Series batteries and includes visual and audible alarms for immediate issue detection. Stay updated and proactive with accurate battery status monitoring. Features: Visible and Audible Warnings and Alarms, Clear 5” Display for accurate battery monitoring, State of Charge, Voltage, Current and remaining Capacity are all clearly displayed.

The ProSport 6 Amp fixed charger is prewired for easy installation and is 100% waterproof and saltwater tested. Its exclusive microprocessor and software ensures that all of the available charging amperage is fully utilized to meet the unique demands of each onboard battery and charge it in the most efficient way. All ProSportHD Generation 4 Chargers boast a new tri-surface heatsink design. This new heavy-duty lightweight design delivers significantly faster charging through optimal cooling, while delivering true rated amp output during charge mode. ProSportHD’s enhanced microprocessor and software provides new digital features including: fuel gauge style Charge Completion Monitor, Charge Mode, individual Fault indicators and three digitally selectable performance charge profiles for Flooded (lead acid), AGM and GEL batteries. Fully automatic 5-stage charging enhances battery performance while extending battery life. System Check OK and Battery Status indicators provide real time installation and battery fault status. Designed for use in harsh environments with our industrial grade jacketed 1.8m DC and AC power cables which include new molded strain reliefs and wire splitters.

The ProSportHD 12 Dual bank 12 Amp fixed charger is prewired for easy installation and is 100% waterproof and saltwater tested. Its exclusive microprocessor and software ensures that all of the available charging amperage is fully utilized to meet the unique demands of each onboard battery and charge it in the most efficient way. After the batteries are charged, the ProSport 12 monitors and maintains the charge only as needed—reducing its AC power consumption. Connection to shore power is made easy by the included 10A plug. The “System Check OK” and “Battery Bank Trouble” LED indicators are exclusive to the ProSport line and confirm the system is operating properly or help shorten any required time spent troubleshooting. Compatible with flooded and AGM batteries, this smart charger provides three charging modes plus a storage recondition mode which helps extend the life of your batteries. Because this charger is waterproof, it can be installed almost anywhere on the boat. All of these features come in a charger that is 40% lighter than conventional epoxy filled (potted) chargers.

The ProMariner ProSportHD 20 operates on exactly the same technology as the ProSportHD 12 above except it is a 20Amp charger and is designed for twin battery setups.

The ProMariner ProSportHD 20 Plus operates on exactly the same technology as the ProSportHD 12 above except it is a 20Amp charger and is designed for triple battery setups. It also has the expanded LED display with a completion status gauge.

SOLD OUT  The ProMariner ProSport 20 Plus is the previous version of the 3 bank 20 Amp HD model above. It just doesn't have the LED indicator. 

Made in Sweden, Zipwake is the world's first Dynamic Trim Control System which incorporates a state of the art series of durable, fast acting interceptors, eliminating the well known trim problems of planing and semi planing hulls. The S Series suits boats between 17 to 50 feet. The system is fully automatic and significantly enhances performance, fuel economy, comfort and safety when accelerating and cornering. Thye have a built in GPS, 3D Gyro and 3D Accelerometer. 

A kit box includes all the parts needed to install a dynamic trim control system with one pair of fast acting interceptors. There are 4 different kit boxes, one for each length of interceptor model. The 4 different kits are the different interceptor lengths of 300mm, 450mm, 600mm and 750mm. The two most common kits by far are the 300mm and the 450mm and are the ones used on all our trailerboats including the large Yellowfin plate boats and the CruiseCrafts.

Each kit contains a pair on interceptors with 3mtrs cables on each, the control panel with a 7mtr cable and the distribution unit with a 4 mtr power cable. Dimensions of the control panel and the interceptors are in the pictures.

The Zipwake Pro series contains all the great features of the Zipwake S System above but adds the following.  Zipwake PRO’s interceptors operate five times faster than previous models, delivering a whole new level of performance and precision. Moving from 0 to 30 or 60 mm in just 0.3 seconds, the increased blade speed enables ultra-fast adjustments to changing conditions. Whether you’re facing wind, waves, or shifting loads, Zipwake PRO responds instantly — optimizing trim and stability for smoother, safer, and more accurate control when it matters most. Check out the last photo for what comes in the Box.

A kit box includes all the parts needed to install a dynamic trim control system with one pair of fast acting interceptors. There are 4 different kit boxes, one for each length of interceptor model. The 4 different kits are the different interceptor lengths of 300mm, 450mm, 600mm and 750mm. The two most common kits by far are the 300mm and the 450mm and are the ones used on all our trailerboats including the large Yellowfin plate boats and the CruiseCrafts.

Each kit contains a pair on interceptors with 3mtrs cables on each, the control panel with a 7mtr cable and the distribution unit with a 4 mtr power cable. Dimensions of the control panel and the interceptors are in the pictures.

The series S PRO Integration is the same kits and specs as the PRO above except it comes with an additional Integration module instead of the standard dahs mounted control module to allow connectivity to most late model sounders/GPS units or Multi Function Displays. Check out the last photo for what comes in the Box.

As boat designs trend toward clean dashboards, larger displays, more flexibility and increased system integration, Zipwake’s Integrator Module gives boat owners a future-proof solution.

SEAMLESS INTEGRATION: Create your perfect set-up. The Integrator Module seamlessly connects the Zipwake system to multiple MFDs from different manufacturers – and even connects wirelessly to smart devices – keeping dashboards free of clutter. But it also offers the flexibility of connecting up to 3 control panels for operation via control wheels in addition to touch screens. A CAN interface enables further external system integration. For assurance, check with your MFD manufacturer to ensure compatibility with Zipwake’s Integrator Module.

WIRELESS CONNECTIVITY: For even greater control, the Integrator Module’s wireless interface lets you configure, operate, monitor, and update the system wirelessly via the Zipwake app on your smartphone or tablet.

EASY TO INSTALL – ANYWHERE: Just slightly bigger than a postcard, the discreet Integrator Module is easy to install behind the helm/dash, on the flybridge or in the engine room. It’s waterproof and comes with a special ethernet connector collar that makes sealing standard ethernet cables easy. A single cable connects the unit to an MFD.

The adaptor plate kits are available in the 300mm and 450mm widths. They allow boaters to easily upgrade to Zipwake from another similarly sized interceptor system. The plates streamline hull preparations to upgrade to Zipwake Series S, fitting perfectly to the existing transom screw hole pattern and sealing previous holes for thru hull fittings. An Adaptor kit includes two adaptor plates, 2 O-rings, screws and an installation guide.