Online Accessories Store

Vertical black aluminium bilge pump switch panel with built in fuse and LED indicator lights in the rocker switch. It has a 3 position switch for auto mode, off and manual on. Dimensions are 85mm X 50mm by 50mm required depth.

This surface mount set has a standard 20mm socket as well as a dual USB socket. There is also a digital volt meter to keep track of your battery voltage. Comes with the dust proof rubber caps. The unit is 130mm wide, 80mm deep and 42mm high.

The brass push button horn switch has a waterproof boot and is suitable for interior and exterior mounting. It is rated to 25 amps for both 12v and 24v applications. Hole diameter for mounting is half inch.

Another very common plug used in a lot of marine applications. It's surface mounted so all you have running through the dash or deck is a small hole for the wires. It screws together so will not come apart in any condition and also has a screw on cap for when not in use. Available with 2 or 4 Pins.

The brass push button horn switch is suitable for interior mounting only and is rated to 25 amps for both 12v and 24v applications. Hole diameter for mounting is half inch.

Perfect for navigation lights this switch is 3 position. The first click turns your rear light on for when you are at rest and the 2nd turns both the rear light and port and starboard lights on for when you are underway. It is suitable for 12v and 24v applications. It has a brass body that fits a 3/8 hole.

The Zipwake Pro series contains all the great features of the Zipwake S System above but adds the following.  Zipwake PRO’s interceptors operate five times faster than previous models, delivering a whole new level of performance and precision. Moving from 0 to 30 or 60 mm in just 0.3 seconds, the increased blade speed enables ultra-fast adjustments to changing conditions. Whether you’re facing wind, waves, or shifting loads, Zipwake PRO responds instantly — optimizing trim and stability for smoother, safer, and more accurate control when it matters most. Check out the last photo for what comes in the Box.

A kit box includes all the parts needed to install a dynamic trim control system with one pair of fast acting interceptors. There are 4 different kit boxes, one for each length of interceptor model. The 4 different kits are the different interceptor lengths of 300mm, 450mm, 600mm and 750mm. The two most common kits by far are the 300mm and the 450mm and are the ones used on all our trailerboats including the large Yellowfin plate boats and the CruiseCrafts.

Each kit contains a pair on interceptors with 3mtrs cables on each, the control panel with a 7mtr cable and the distribution unit with a 4 mtr power cable. Dimensions of the control panel and the interceptors are in the pictures.

6 gang RECTANGULAR Stainless Steel switch panel with 15A backlit switches. The 15 Amp Backlit Switches are all pre-wired and are designed to make your life easier and more stylish. Boasting a bright and clear backlit display when pushed and turned on you just fit the appropriate decal for what its being used for. Switch label stickers are supplied as per photo. Face plate dimensions are 80mm by 112mm. and it can be mounted either vertical or horizontal as the writing on the faceplate is multi directional.

The BEP Splashproof Switch Panels are a stylish and quality contoured, moulded plastic panel with a removable cover plate over the switches to conceal the screws. Each switch has a backlit LED Red or Green light so you can see at a glance if they are on or off. They are available with and without fuses (blade type) and both come standard with a 29 piece label set. Suitable for 12volt only. Height = 158mm, Width = 110mm with a 75mm intrusion.

We use this one all the time in our Cruisecraft and Yellowfin boats. The Battery Management System makes twin battery charging easy! Pre-assembled module with solid links and application labels combining three 701 Mini Battery Master Switches with a 100 amp Voltage Sensitive Relay. It's easily connected to the existing wires, providing a fully automatic battery management system and provides for isolation of start and house batteries independently with the ability to emergency parallel supply from both. The VSR  (Voltage Sensitive Relay) automatically prioritises charging of the start battery. When the engine is first started the relay is open and remains open until the start battery has reached a preset 13.7 volt. At the rated Voltage, the relay closes providing charge to both batteries (start and house). When the Voltage drops below 12.8 volt (when the engine is stopped), the VSR disengages, separating the batteries. It eliminates possibility of draining the start battery and protects electronics powered by the house battery from harmful engine starting spikes. Dimensions are 140mm X 140mm wide X 75mm.

Matt black aluminium switch panel with 6 red illuminated rocker switches and 6 circuit breakers. Comes with 2 by 5amp, 2 by 10amp and 2 by 15amp circuit breakers. Suitable for 12volt only. Height = 165mm, Width = 115mm.

This deluxe rocker switch with LED light is rated to 20amps and can either be mounted on its own or as a replacement in an existing panel. Suitable for 12 or 24volt applications. Comes with sealing gasket and fastens using locking tabs fixed to switch. Hole cutout is approx 20mm X 35mm.

This 3 position switch suits 12 and 24volt applications. The middle position is off and then you can flick either up or down for on. Hole diameter for mounting is 12mm.

12volt plastic flush mounted socket with splashproof rubber lid. Requires a 27mm hole for mounting and suits all standard 20mm accessory plugs. Perfect for charging phones, spotlights and 12v air pumps for blowing up tubes and biscuits.

Made in Sweden, Zipwake is the world's first Dynamic Trim Control System which incorporates a state of the art series of durable, fast acting interceptors, eliminating the well known trim problems of planing and semi planing hulls. The S Series suits boats between 17 to 50 feet. The system is fully automatic and significantly enhances performance, fuel economy, comfort and safety when accelerating and cornering. Thye have a built in GPS, 3D Gyro and 3D Accelerometer. 

A kit box includes all the parts needed to install a dynamic trim control system with one pair of fast acting interceptors. There are 4 different kit boxes, one for each length of interceptor model. The 4 different kits are the different interceptor lengths of 300mm, 450mm, 600mm and 750mm. The two most common kits by far are the 300mm and the 450mm and are the ones used on all our trailerboats including the large Yellowfin plate boats and the CruiseCrafts.

Each kit contains a pair on interceptors with 3mtrs cables on each, the control panel with a 7mtr cable and the distribution unit with a 4 mtr power cable. Dimensions of the control panel and the interceptors are in the pictures.

This is the twin battery switch above with a Voltage Sensitive Relay (VSR) all pre-wired in. With the selector switch in position 1, it becomes the sensing battery for the VSR. When the engine is first started the relay is open and remains open until the selected battery reaches a pre-set 13.4 volt. The relay closes at the rated voltage providing charge to both batteries. When the selected battery voltage drops below 12.8 volt, the DVSR disengages, separating the batteries and ensuring that battery 1 is not discharged by house loads. When the selector switch is in position 2, this becomes the sensing battery and the reciprocal occurs. When the selector switch is in the both position the DVSR is inactive and the charge and load is distributed evenly between the batteries. With this system the loads are run off the same battery as the engine starting battery. Dimensions are 69mm X 69mm X 138mm.

15 Amp push button switch to suit switch panels above. They don't have to be mounted in the panel and as they are IP67 waterproof they are great to just fit on their own out in the open somewhere. Note: Stickers are supplied separately below.

6 gang INLINE Stainless Steel switch panel with 15A backlit switches. The 15 Amp Backlit Switches are all pre-wired and are designed to make your life easier and more stylish. Boasting a bright and clear backlit display when pushed and turned on you just fit the appropriate decal for what its being used for. Switch label stickers are supplied as per photo. Face plate dimensions are 52mm by 203mm.

This 20mm plug suits all standard 12 and 24 volt sockets. It is ideal for powering multiple electronic devices with dual USB plugs from a boat or vehicle’s accessory socket. Features easy to read battery Volt meter which switches to Amp draw when a device is plugged in to one of USB sockets

Suitable for 12V-42V applications this is a recessed version of the breaker above. They are waterproof and resetable. Suitable for all marine applications including inside engine boxes.

These twin tin plated brass buss bars with insulated mounting bases come in 2 sizes. They both sit 15mm high and the 12 takeoff is 120mm long while the 24 take off is 120mm. The mounting holes are recessed to avoid accidental shorts. Both are supplied with the required amount of stainless screws and split washers to suit.

12v in line Rule bilge blower with either a 75mm or 100mm inlet and outlet. They have a sealed motor shaft for moisture protection and are very low amp draw.

A common plug used in a lot of our boats. It has a standard 20mm socket on one side and a digital volt meter on the other. Suitable for 12 and 24volt applications. Dimensions of panel are 105mm long by 43mm high.

Surface Mounted 12volt socket to suit all 20mm plugs. Screw distance apart is 44mm.