Online Accessories Store

This is a popular option and is found in many boats. It is made from white polypropylene and has a clear watertight locking hatch. Each draw also has a clear locking lid. Outer dimensions are 364mm X 183mm and the cutout is 321mm X 140mm and requires 150mm depth. The draws are 130mm X 150mm X 50mm.

These white polypropylene boat boards are tough against cuts and UV deterioration. The size of the board is 700mm by 420mm and they can be purchased in either a twin rod holder or 25mm twin rail mount setup. Both models have adjustable width mounting from 285mm to 580mm so will fit almost any setup. Both mounting setups also feature an adjustable thumbscrew ratchet which allows the table to be fixed at the desired angle.

The heavy duty cast holder is designed to accept and securely hold most common rods but also allows the rod to be quickly removed when fish strike. Each holder is mounted on a cast stainless steel base which is designed to be clamped around hand rails or rod racks manufactured from 25mm diameter tube. The heavy duty cast rod holder can be swivelled to best suit any desired rod angle. It rotates through 360 degrees in both the horizontal and vertical axis.

Replacement base for standpipe above.

WANT TO PLUMB UP YOUR EXISTING LIVE BAIT TANK? Flow-Rite’s Standpipe is an essential component for livewell plumbing systems and provides a secure and watertight seal between the drain hole and it also acts as the overflow. It features a threaded bottom that allows for easy installation into either the straight or elbow fittings below. It also has 2 holes within the thread so you can just unscrew it a bit to let some water out without having to take the whole pipe out and risk losing bait down the drain. Its 18" tall so you just remove the top cap and cut it down if needed.

Made from white flexible pvc they were originally designed to hold winch handles on yachts. They are now use almost exclusively for either holding a trailer winch handle or fishing knives. Its approx 300mm high and 90mm wide. Can be mounted anywhere with 3 stainless screws or bolts at the top.

Made from Stainless Steel and then Titanium coated, the AFN Pro Plus Pliers cut through both braided and mono lines. Made from stainless steel for durability, and with a soft spring loaded non slip handle they are easy to use. They also have a micro split ring opener and come with a clip on bungee lanyard and pouch to prevent accidental loss overboard. Overall length is 140mm and the long nose plyers length back to the pivot is 60mm so you can reach deep into the fish's mouth to remove the hook more easily.

The Sea Pro Deluxe Floating Net is ideal for river, inshore and offshore work. Thanks to the handle and the floating structure, it can be easily recovered in case of accidental release. The mesh is rubber and the net head is 40cm wide at mouth and 45cm long on the large model and 30cm wide by 35cm long on the small. Collapsed the over all length is just 68cm and when extended its 160cm long for the large and 45cm and 80cm for the small. It has a soft foam rubber hand grip with elastic wrist strap with clip.

There are 2 poles and 2 of everything in this kit. This is the same kit as above except these bases are designed to be mounted on the side of a cabin, hard top or rocket launcher. Five year warranty! Sold as a pair.

The Railblaza RodStow rod holder system is a vertical fishing rod storage rack and caddy for boats. RodStow rod racks will hold your rods above deck, safely and securely. The RodStow Double is available in black or white, comes with stainless steel fasteners and can be installed in minutes. It features a storage caddy for lures, traces and other tackle, it's even big enough to hold a small tackle box. These rod holders have a removable gimbal pin that you can leave in to support the rod and stop rotation, or remove to let the rod pass through. 40mm tube sizes caters for most equipment.

These are our simple to use electric work horses featuring extendable booms and swivel bases. They are perfectly suited to all the saltwater species you can target – from tuna to mackerel to kingies – you will get to the fish. 

Features
• Auto-Up feature retrieves the weight at the push of a button
• Dual axis adjustable rod holder
• IP68 waterproof power cord
• Removable side plate for easy spool access
• Includes mounting base and low-profile swivel base
• Three-digit depth counter
• Integrated ball storage hook
• 20lb ball weight weight capacity
• Includes line release and 76m of 68kg stainless steel cable
• Corrosion-resistant construction

Made from heavy duty Lexan and stainless steel it has six point locking, including two 45° positions. Suits all downriggers except Lake Troll and Mini Troll. Stainless steel mount fastenings included to connect to up to 6mm thick deck. Dimensions are 189mm L by 146mm W by 29mm H.

New Game Rated Version fully welded at the neck and available in 0, 15 & 30 Degrees,  these stainless rod holders are fully welded and designed for those tight spaces or narrow gunnels. They can also be used to hold your bait board legs, BBQ, Downrigger etc etc. The tube Id is 41mm, the tube wall is 1.5mm, height is approx 230mm (from under the flange) and the top flange is a 5mm thick plate with dimensions of 83mm X 60mm with 4 fixing holes.

Made from 316 Stainless Steel, this is a popular heavy duty fully adjustable rod holder extension with a 42mm Inside diameter tube to take the rods. It rotates 360 degrees as well as vertically 180 degrees. The bottom tube size is OD42mm and the bottom and top tube lengths are 323mm to pivot point so 646mm overall.

This is the heavy duty 30Ltr tank above plus all the fittings and plumbing you will need as displayed in the 2nd picture. 2 by 1.6mtr sections of hose are also included and the only additional thing you will need is just some 12v wiring and switch or just wire it up to a spare switch panel that you already have in the boat. 

The Railblaza RodStow rod holder system is a vertical fishing rod storage rack and caddy for boats. RodStow rod racks will hold your rods above deck, safely and securely. The RodStow Double is available in black or white, comes with stainless steel fasteners and can be installed in minutes. It features a storage caddy for lures, traces and other tackle, it's even big enough to hold a small tackle box. These rod holders have a removable gimbal pin that you can leave in to support the rod and stop rotation, or remove to let the rod pass through. 40mm tube sizes caters for most equipment.

Great kids landing net. Features 20cm opening plus 37 to 86cm extendable handle. Stainless steel with polyester mesh net plus non-slip cushioned grip. Available in Blue or Pink.

With its stainless steel spool and white housing, the Optimum TS downrigger wirelessly networks together giving you control of all of your downriggers with the push of a button. They connect with your Humminbird fish finder and your mobile device for total control and to display trolling data. With the One-Boat Network, your advanced fishing gear does more than work together. It starts talking to each other wirelessly, to help you find, stay on and land more fish. The full-colour 4” display shows critical trolling data right on your downrigger, taking the guess work out of your trolling presentation.

The Cannon mobile app connects to your Optimum TS downriggers, putting you in total control. Set, cycle or raise weights, access Fish Hawk sensor data…it’s all there at your fingertips. Every Optimum TS downrigger integrates wirelessly with the Fish Hawk X4D to give you the info you need to troll successfully. You’ll know more than surface water temp and speed. Your Optimum TS display will also show you the true depth, trolling speed and temperature at the weight. Through the One-Boat Network, you can also access this data through your mobile device and Humminbird fish finder.

Features
• Auto Up allows you to retrieve weights simultaneously
• across networked downriggers with the push of a button
• Bottom Tracking keeps your bait presentation at a
• precise distance off of the bottom
• Depth Cycling – Cycle your bait within a set depth range
• Positive Ion Control
• Waterline Zero
• Telescopic boom extends from 24” to 53”
• 250 feet-per-minute retrieval speed
• 20-lb weight capacity

The Mag 5 opens the door to our Electric Downrigger family. If you are fishing alone there is no bigger advantage to an electric retrieval of your bomb when you hook a fish. Just flick the switch and it will bring your bomb up so you can get back to fishing. The Mag 5 has a fixed spool length and does not include the swivel base of the Magnum 10 STX models.

Features
• Auto-Up feature retrieves the weight at the push of a button
• Dual axis adjustable rod holder
• IP68 waterproof power cord
• Removable side plate for easy spool access
• Three-digit depth counter
• Includes mounting base
• Integrated ball storage hook
• 20lb ball weight capacity
• Includes line release and 76m of 68kg stainless steel cable
• Corrosion-resistant construction

Both Uni-Troll 10 downriggers share the same features except the TORN has a stainless steel spool and a white housing.

The Uni-Troll 5 shares the same Features as the Uni-Troll 10 STX except that it has a fixed heavy duty boom and does not include a swivel base as standard.

Features
• 21 retrieval speed
• One-hand clutch deploy for simple, precise bait positioning
• Enclosed boom end pulley prevents line jumping
• Easy-access universal mounting base
• Dual axis rod holder – fully adjustable in all directions
• Heavy duty stainless steel 61cm boom
• Includes mounting base
• 20lb ball weight capacity
• Ergonomic crank handle
• Integrated ball storage hook
• Three-digit depth counter
• Pre-spooled with 61m of 68kg test stainless steel cable and includes a line release

Cast lead downrigger weights with brass attachment points. Designed for use on all downriggers.

Made from black powder coated aluminium, it will let you mount any of the Cannon downrigger range, (except Mini-Trol), into an existing rod holder. The pad is pre-drilled to accept all bases. They have a solid 13mm thick top mount pad which measures 127mm by 127mm and an extra heavy duty 6mm wall thickness support tube. Stainless steel mount fastening included. Tube diameter is 38mm and the two shaft lengths are either 9 inch or 12 inch.

With a 10mm shaft diameter they fit any size of rowlock holder and are a great addition to any tinnie. The tube is 150mm long. They are made from 304 stainless and have plastic end caps so your rods and reels wont get harmed.