Accessories

This Rule float switch suits both 12V and 24V pumps up to 14 Amps (2000 GPH). It turns on when the water level reaches 2" and turns off when it reaches 3/4".

This is the Automatic version of the pump above. This is also a new low profile version that sits only 60mm high and the outlet can be angled either up or to the side. It comes with the 4 output nozzles of 19mm straight and elbow, 25mm straight and 28mm straight. Output capacity is 900 GPH or 3407 LPH.

Rule is one of the most popular brands of bilge pumps on the market. All pumps are fully submersible and ignition protected with low amp draw. This is a new low profile version that sits only 60mm high and the outlet can be angled either up or to the side. It comes with the 4 output nozzles of 19mm straight and elbow, 25mm straight and 28mm straight. Output capacity is 900 GPH or 3407 LPH. This is the manual version.

This Rule float switch suits both 12V, 24V and 36V pumps up to 20 Amps. It's encased in an impact resistant plastic cover to protect against debris fouling the float switch. The base is also removable for easy installation and maintenance. It turns on when the water level reaches 2" and turns off when it reaches 3/4".

This Rule float switch suits both 12V, 24V and 36V pumps up to 20 Amps. It turns on when the water level reaches 2" and turns off when it reaches 3/4".

These Rule transom mount live bait tank pumps are a great product and are what we use a lot of the time in our workshop. The outlet swivels 360 degrees so there are no issue with positioning. There is a 2nd outlet port available located below the pump motor for use for an optional deck wash so you only have to have the one fitting through the boat. Outlet size is 19mm or 3/4" for the 500 and 800 models and 28mm for the 1100 model.

These Rule thru hull live bait tank pumps are a great product and are what we use a lot of the time in our workshop. The outlet swivels 360 degrees so there are no issue with positioning. There is a 2nd outlet port available located below the pump motor for use for an optional deck wash so you only have to have the one fitting through the boat. Outlet size is 19mm or 3/4" for the 500 and 800 models and 28mm for the 1100 model.

Rule replacement round base strainer to suit 360 and 500 GPH pumps.

The all NEW versions of the Rule-Mate fully automatic submersible bilge pumps offer a more compact size with high performance & reliability. They are a more compact size being only 2/3 the size of the previous models. They have an internal water level sensor and will activate when the bilge water level reached 62mm height and will shut off when it drops to 16mm. Supplied with a 20mm (3/4") straight hose outlet. Dimensions are 73mm wide, 129mm long (165mm long with straight hose fitting) and 112mm high. Output capacity is 500 GPH or 31 LPM, 800 GPH or 50 LPM and 1100 GPH or 69 LPM.

Whilst at first this kit may look expensive, it's actually a very good idea and you also get the 90ltr heavy duty PVC woven bag with waterproof moulded EVA base. The bag dimensions are 750mm by 360mm by 360mm and is great for an emergency fish kill bag. The kit contains 4 jackets, waterproof torch with batteries, V sheet, 1kg fire extinguisher, signalling mirror, pealess whistle, bailer scoop and 2 telescopic paddles. It does NOT come with flares as they cannot be shipped however we sell them in store. Don't forget you will also need an anchor, rope and chain so if you look in the Anchoring/Mooring/Ropes section there is a great selection as well as a perfect portable folding anchor kit that will fit in the bag.

For use in all salt water cooled engines, inboards, outboards and jet skis. It removes salt deposits and protects your engine from corrosion. Simply add 50mls of Salt Engine Flush concentrate to the engine flush adaptor below, place adaptor in-line between the garden hose and the engine water inlet and turn on the tap. The flow of engine flush concentrate can be adjusted up or down to determine the length of the flush time but a few minutes is heaps. Continue to flush the engine for a further 2 minutes with just fresh water to remove the last of the concentrate. NOTE: The engine does not have to be running for this product to work. You can use the static flush port found on most late model engines or you can use earmuffs for older engines.

The most popular of all anchors. With a heavy duty hot galvanised finish they are suitable for mud or sand. The anchor size refers to the approximate weight in pounds (lb). Make sure you choose the right size for your boat.
4lb - Boats up to 3 mtrs
6lb - Boats up to 4 mtrs
8lb - Boats up to 5 mtrs
10lb - Boats up to 6 mtrs
13lb - Boats up to 7 mtrs

This is what we use for the safety gear packs for all of our boats. Available in 3 sizes they come with 50mtrs of rope in the correct size, 2 gal shackles, stainless eye in the end of the rope and the correct amount of chain.
6lb kit - 50m by 6mm rope and 2m by 6mm chain.
8lb kit - 50m by 8mm rope and 4m by 8mm chain.
10lb kit - 50m by 10mm rope and 4m by 8mm chain.

Santorini 350mm steering wheel with brushed aluminium spokea and a polyurethane grip with inserts. It's 350mm diameter and the offset is 55mm to the back of the grip from the dash and 85mm to the front of the grip. It is supplied with the hub which suits any 3/4 inch tapered shaft and then is adjustable via the 6 hex head bolts so it can be rotated for easy wheel alignment.

SARCA is the first Sand And Rock Combination Anchor that actually works. The Hoop on the rear of the anchor ensures that the Super SARCA rolls over in most situations, allowing the toe to be in its best possible position to penetrate the ocean floor and reducing dragging as the fluke digs in. They incorporate an automatic reset trip release that offers you the highest rate of recovery from rocks. When anchoring in and around bommies, reef or coral the Super SARCA has less chance of getting stuck and will create less damage to the environment. If snagged, you tie off the rope and as you drive over the anchor the shackle slides up the shaft to pull the anchor out backwards. Make sure you always use a stainless shackle though so it slides easy. Use the table in the picture to work out the correct size for your vessel.

The next in the range is the 1000. Everything in the main picture is supplied in the box. The 2nd picture is the dimensions of the complete winch. The last picture shows what length of chain and rope it comes with. Below if needed is the Hawse pipes, bow sprits, genuine Savwinch anchors and wiring loom kits. CLICK HERE for the full installation manual for all models.

The largest in the range is the 1500. Everything in the main picture is supplied in the box. The 2nd picture is the dimensions of the complete winch. The last picture shows what length of chain and rope it comes with. Below if needed is the Hawse pipes, bow sprits, genuine Savwinch anchors and wiring loom kits. CLICK HERE for the full installation manual for all models.

The Savwinch Signature Series (SS) is their premium range of Drum Winch and is what we fit on all our trailerboats. As we fit them inhouse, we genuinely know what we are talking about and are only a phone call away if advice is needed. They feature a complete stainless steel motor, designed locally and exclusively for Savwinch. Machined to fine tolerances and utilising O ring seals, the SS series motors are IP68 rated and are completely submersible without the use of sealants or glues. You no longer need to be concerned about water ingress or corrosion. The motors can be moved into 12 different positions to ensure that each Drum Winch can be installed on almost any vessel.

Once you select the correct size for your boat, the winch is generally mounted on the rear of the anchor locker, provided it is strong enough and reinforced with the backing plate on the inside of the boat. If you have an aluminium boat like a Quintrex with a roto moulded anchor well then just purchase the plate below and still mount the winch inside the anchor locker but bolt it to the plate upside down and bolt the plate across the top of the anchor well. They can also be mounted just on top of the deck. Check out all the pictures as one of them shows the different mounting options and what extra may be needed. The only one its doesn't show is when you mount the winch upside down to the custom plate below that is bolted across the top of the anchor well. (What we use on Quintrex and Stacer boats)

Everything in the main picture is supplied in the box. The 2nd picture is the dimensions of the complete winch. The last picture shows what length of chain and rope it comes with. Below if needed is the Hawse pipes, bow sprits, genuine Savwinch anchors and wiring loom kits. CLICK HERE for the full installation manual for all models.

The next in the range is the 880. Everything in the main picture is supplied in the box. The 2nd picture is the dimensions of the complete winch. The last picture shows what length of chain and rope it comes with. Below if needed is the Hawse pipes, bow sprits, genuine Savwinch anchors and wiring loom kits. CLICK HERE for the full installation manual for all models.

Significantly quieten your chain so that you don’t scare away the fish! Our Chain Guard Sock is exclusively manufactured for Savwinch. Made from a custom thick sleeving which reduces almost all of the noise from the chain going over the Bowsprit. The thick custom material stretches over both 6mm and 8mm chain which allows the chain to breathe, ensuring you don’t get any sand/mud/seaweed stuck in the sleeving. Available in 7mtr or 9mtr lengths.  

When you have an anchor well that is not strong enough to bolt the winch to, (like plastic Roto moulded wells on Quintrex and Stacer) then you fit this plate across the top and bolt the winch up to it from underneath. That way the winch is still hidden inside the anchor well. Works best with the 880 winch.

Slider anchors (also known as escape anchors) feature a full sliding ring along the shaft. The advantage of the full sliding action is that it allows you to drive over the top of your anchor, slide your chain down the shaft and pull it out when reefed or caught. Savwinch features the Delta Style design Anchor you’ve known to love. Whilst also having the excellent holding power of a traditional anchor with the added benefit of a Sliding ring. Use the chart below as a guide, if unsure then always go larger. You can get Galvanised and Stainless Steel in each size.

4kg    - Boats up to 4.5m
6kg    - Boats up to 5.5m
7.5kg - Boats up to 7m
9kg    - Boats up to 8m
16kg  - Boats up to 11m
20kg  - Boats up to 15m

The 316 Stainless Steel Savwinch Signature Bowsprit is designed to secure and house your anchor and suits almost all boats. This is our high end, premium Bowsprit which starts with a large piece of Stainless Steel that is folded, a second piece of Stainless Steel is then welded to the top, which is then polished our to create the perfect Bowsprit. The signature Bowsprit features 3 rollers, which allows for quick and easy anchor retrieval every time. If you look at the 1st picture you can see the 3 axle bolts along the side showing where the 3 rollers are. Dimensions are 78mm X 430mm.

If you don’t have an open Anchor Well and you don’t want to Deck Mount your Drum Winch you will require a Hawse Pipe. A Hawse Pipe gives a nice clean look and ensures the Winch is hidden away within the boat. Made from 316 stainless the small is great for boats under 7mtrs and suits almost all our trailer boats. the large is for boats over 7mtrs. The small has a base of 168mm X 100mm and an opening of 100mm X 48mm. The large has a base of 223mm X 100mm and an opening of 154mm X 48mm.