hunts marine

The BEP Splashproof Switch Panels are a stylish and quality contoured, moulded plastic panel with a removable cover plate over the switches to conceal the screws. Each switch has a backlit LED Red or Green light so you can see at a glance if they are on or off. They are available with and without fuses (blade type) and both come standard with a 29 piece label set. Suitable for 12volt only. Height = 158mm, Width = 110mm with a 75mm intrusion.

Same top quality BEP Contour switch panel as above except it has 6 built in Positive Temperature Coefficient (PTC) resettable fuses. PTC fuses are solid state 9 amp resettable fuses where all you do is turn the particular switch off for 10 secs to reset. Comes standard with a 29 piece label set. Suitable for 12volt only. Height = 158mm, Width = 110mm with a 75mm intrusion.

This Contour BEP switch panel suits both 12volt and 24volt applications. They are an injection moulded plastic panel with modern contour styling with a switch tray featuring a Rubber mounting gasket and integral cover seal. They come in 2, 4 and 6 gang with or without fuses and then you can also choose between black or white. Both black and blue interchangeable contour wave trims are included and the panels can be mounted horizontally or vertically due to the unique label design that is readable from both angles. They have a Red LED indicator light to show when the switch is turned on. Dimensions are all 63mm wide with a 25mm intrusion and then the length is 71mm for the 2 gang, 119mm for the 4 and 167mm for the 6. All BEP Splashproof Switch Fuse Panels are supplied complete with a 28 piece label set. 

This BEP on/off battery switch is high quality and small so it perfect for trailer boats where a nice neat installation is crucial. It's rated to 275 amp continuous, 455 amps intermittent and 1250 amps cranking. It suits applications up to 48volt. Dimensions are 69mm X 69mm X 75mm.

This BEP twin battery switch is high quality and small so it perfect for trailer boats where a nice neat installation is crucial. It's rated to 200 amp continuous, 300 amps intermittent and 1000 amps cranking. It suits applications up to 48volt. Dimensions are 69mm X 69mm X 75mm.

This is the twin battery switch above with a Voltage Sensitive Relay (VSR) all pre-wired in. With the selector switch in position 1, it becomes the sensing battery for the VSR. When the engine is first started the relay is open and remains open until the selected battery reaches a pre-set 13.4 volt. The relay closes at the rated voltage providing charge to both batteries. When the selected battery voltage drops below 12.8 volt, the DVSR disengages, separating the batteries and ensuring that battery 1 is not discharged by house loads. When the selector switch is in position 2, this becomes the sensing battery and the reciprocal occurs. When the selector switch is in the both position the DVSR is inactive and the charge and load is distributed evenly between the batteries. With this system the loads are run off the same battery as the engine starting battery. Dimensions are 69mm X 69mm X 138mm.

These BEP switch panels suits both 12volt and 24volt applications and have a built in 20mm power socket. All BEP Splashproof Switch Fuse Panels are supplied complete with a 28 piece label set. They are high quality and not a cheap copy. They are all pre-wired and have spade fuses already wired into the back of the units for easy installation. They come in both BLACK and WHITE in each size. The dimensions of the 3 and 5 gang panels are the same. Overall Size: 107mm x 95mm Cut Out Size: 87mm x 75mm Intrusion: 75mm. Labels Supplied: Anchor Light, Accessories, Aerator, Autopilot, Bait Tank Pump, Bilge Pumps, Blower, Cabin Lights, Cockpit Lights, DC Outlets, Deck Wash, Depth Sounder, Fridge, Freshwater Pump, GPS, Horn, Instruments, Inst. Lights, Navigation Lamps, Radar, Spare, Spot Light, Stereo, Stern Light, Trim Tabs, VHF, Winch & Wiper.

These BEP switch panels suits both 12volt and 24volt applications. All BEP Splashproof Switch Fuse Panels are supplied complete with a 28 piece label set. They are high quality and not a cheap copy. They are all pre-wired and have spade fuses already wired into the back of the units for easy installation. They come in both BLACK and WHITE in each size. The dimensions of the 4 and 6 gang panels are the same. Overall Size: 107mm x 95mm Cut Out Size: 87mm x 75mm Intrusion: 55mm. Labels Supplied: Anchor Light, Accessories, Aerator, Autopilot, Bait Tank Pump, Bilge Pumps, Blower, Cabin Lights, Cockpit Lights, DC Outlets, Deck Wash, Depth Sounder, Fridge, Freshwater Pump, GPS, Horn, Instruments, Inst. Lights, Navigation Lamps, Radar, Spare, Spot Light, Stereo, Stern Light, Trim Tabs, VHF, Winch & Wiper.

This BEP switch panel suits both 12volt and 24volt applications and has a built in USB dual charging socket. All BEP Splashproof Switch Fuse Panels are supplied complete with a 28 piece label set. They are high quality and not a cheap copy. They are all pre-wired and have spade fuses already wired into the back of the units for easy installation. Overall Size: 107mm x 95mm Cut Out Size: 87mm x 75mm Intrusion: 55mm. Labels Supplied: Anchor Light, Accessories, Aerator, Autopilot, Bait Tank Pump, Bilge Pumps, Blower, Cabin Lights, Cockpit Lights, DC Outlets, Deck Wash, Depth Sounder, Fridge, Freshwater Pump, GPS, Horn, Instruments, Inst. Lights, Navigation Lamps, Radar, Spare, Spot Light, Stereo, Stern Light, Trim Tabs, VHF, Winch & Wiper.

BEP Battery Distribution Cluster is a pre assembled module with solid links and application labels, based on the 701 Mini Battery Master Switch. BEP Battery Distribution Cluster provides for isolation of start battery and house batteries independently with the ability to emergency parallel supply from both. Ignition protected. Dimensions are 200mm high X 69mm wide X 75mm deep.

This is exactly the same as the square unit above except its available in either a vertical row or a horizontal row. The horizontal row is part number 114070 and the vertical is part number 114074. Dimensions are 69mm X 276mm wide X 69mm.

We use this one all the time in our Cruisecraft and Yellowfin boats. The Battery Management System makes twin battery charging easy! Pre-assembled module with solid links and application labels combining three 701 Mini Battery Master Switches with a 100 amp Voltage Sensitive Relay. It's easily connected to the existing wires, providing a fully automatic battery management system and provides for isolation of start and house batteries independently with the ability to emergency parallel supply from both. The VSR  (Voltage Sensitive Relay) automatically prioritises charging of the start battery. When the engine is first started the relay is open and remains open until the start battery has reached a preset 13.7 volt. At the rated Voltage, the relay closes providing charge to both batteries (start and house). When the Voltage drops below 12.8 volt (when the engine is stopped), the VSR disengages, separating the batteries. It eliminates possibility of draining the start battery and protects electronics powered by the house battery from harmful engine starting spikes. Dimensions are 140mm X 140mm wide X 75mm.

Completely adjustable to suit any brand of phone. Though HoldFastPro was born while creating the best cell phone holder for boats, they have found endless possibilities to secure the adjustable cell phone holder too! Order yours today and save the drink holders on your next boating trip for drinks! Made of durable, high impact plastic, 2 Velcro straps provided to secure to most T-Top Consoles and round poles – adjust the phone holder strap to a round pole 1 inch to 5 inches and keep your phone safe, secure, and at your fingertips. Sunglass hanger attached to phone holder Not just limited to use on your boat, can be used on beach umbrellas, golf buggies and more. CLICK HERE to watch a quick YouTube clip on how it works.

12v in line Rule bilge blower with either a 75mm or 100mm inlet and outlet. They have a sealed motor shaft for moisture protection and are very low amp draw.

75mm or 100mm concertina high flow bilge blower hose. Price for a 3mtr length when extended. This will suits almost all boats but if you do need longer then please give us a call as we can order in a 15mtr length. 

This is actually a pretty good product. The versatile sun shade kit extends the shaded area of the Bimini and allows airflow. It gently filters the sun rays to provide a comfortable shaded  area. fastening on to only your existing bimini frames and using your two rear rod holders, it takes only a few minutes to install and is easily folded for compact storage. Can be used at anchor or motoring up to 20 knots. Its available in two sizes and the 3 colours of Grey, Navy and Black in each size. See additional pictures for full dimensions.

Another good buy. It has an output capacity of 19 LPM, is self priming with an adjustable pressure switch, has rubber mounted feet for corrosion protection and noise reduction, runs dry without damage and is ignition protected. The coiled hose extends up to 25 feet and coils up back to approx 16" so takes up very little storage space. It also comes with a strainer, hand nozzle and 2 by half inch hose connectors.