Online Accessories Store

85mm plastic square air vent available in either black or white with a 75mm tail to suit bilge blower hose.

Same pole and base as above except the table is rectangular and has 4 inbuilt cup holders. Table dimensions are the same at 760mm by 460mm.

Why not have a table position up the front in the bow rider section as well as down the back? This is the same table base and specs as above. 

Using the same outer scupper valve as above, it has a 75mm threaded shaft that then takes a 38mm hose so you can connect it up to a floor drain as per the picture. Also supplied with the 4 stainless mounting screws. The overall length is 157mm and the cut out hole size is 45mm.

This stainless steel recessed drink holder has an internal diameter of 70mm to suit all canned drinks and is 40mm deep.

One of the most common plastic glove boxes used in most open boats, runabouts and half cabins. It has a stylish front and is also lockable. Lid dimensions are 350mm wide and 135mm high and the box is 160mm deep.

Available in 4 lengths from 229mm to 610mm these Stainless Steel Handrails are made from 316 grade mirror finish 22mm diameter stainless steel tubing. Each end has a Marine-grade nylon base and they come with the mounting stainless bolts, nuts and washers.

90mm white plastic square air vent suitable for a number of different applications.

This stainless steel drink holder has 2 internal sizes to suit either a wine bottle or can snugly. Cutout size is approx 90mm and then there is an 8mm lip. Depth is 90mm. They have a small 1/4 inch drain fitting on the base so they can be plumbed out the sides or internally if required.

Replacement quick release pin kit to suit both stainless steel bow rollers above.

White, polypropylene battery clamp down set. Nylon bolts and wing nuts will not rust or corrode. Impervious to battery acid. Maximum battery height 200mm and minimum height 155mm, maximum width 170mm. 4mm countersunk mount screws.

Made from polished 304 grade pressed stainless steel, all 4 stainless louvre vents are pre-drilled for 4mm fastenings. Dimensions of all 4 are in the main picture.

One of the most common air vents on the market. Made from UV stabilised plastic the outer base dimensions are roughly 190mm by 150mm and the offset raised 70mm diameter air hole in the inner plate prevents any water entry into the boats cabin that may enter the vent.

This is a great little flush mounted storage unit and can be used for almost anything including tackle. It has 5 draws and a waterproof door. The outer dimensions are 364mm by 183mm with a depth of 150mm. Draw size is 130mm by 150mm by 50mm high.

This is a very common shower head on/off nozzle and is used on a lot of trailer boats including the Whittley models we sell. Fits the hoses and housings below.

The adaptor plate kits are available in the 300mm and 450mm widths. They allow boaters to easily upgrade to Zipwake from another similarly sized interceptor system. The plates streamline hull preparations to upgrade to Zipwake Series S, fitting perfectly to the existing transom screw hole pattern and sealing previous holes for thru hull fittings. An Adaptor kit includes two adaptor plates, 2 O-rings, screws and an installation guide.

Made from solid chrome plated brass, this bow roller has been around forever and is extremely strong. It has a spring loaded retaining pin that can never completely fall out. The overall length is 145mm, max width is 75mm and the roller width is 25mm.

This heavy duty cast 316 grade stainless steel split bollard with spring loaded pin allows securing and fastening of the anchor chain. The split can accept 8mm to 13mm chain depending on the size. The smaller unit has a 60mm by 60mm base and is 84mm high and can take chain size up to 10mm. The larger unit has a 85mm by 85mm base and is 115mm high and can take chain up to 13mm. Both sizes take 6mm fastening screws or bolts.

These sleek low profile hatches are designed for use on all boats from powerboats, sailboats and large yachts. With a 25mm profile above the deck and as low as 19mm if counter sunk in teak decks, the sleek minimalist lines add style to any vessel. With smoked acrylic glass and an anodised aluminium frame they utilise a unique heavy-duty anodised aluminium frame. The larger escape hatches are designed with two struts and two twist locks and the smaller ventilation hatches use one strut and one locking lever. Each strut comes standard with a twist lock brace to hold the lid in any position up to 95 degrees. A quick release pin enables the struts to be detached from the frame, allowing the hatch to open to a full 180 degrees.

Attractive, strong and corrosion resistant, these solid bar cleats are made from polished 316 stainless and will last a lifetime.

A 5 step rope ladder that folds up flat after use for easy storage. It has red polypropylene steps with a dimpled finish for extra grip. There's plastic reinforcing tube between steps for added boarding stability. Total length is 1.5Mtr.

New Zealand made quality 4" Nairn inspection port with recessed lid with 4 finger grips. Available with Black or White surround.

Flat edged popular screw in bung with chrome brass housing.

Made in Sweden, Zipwake is the world's first Dynamic Trim Control System which incorporates a state of the art series of durable, fast acting interceptors, eliminating the well known trim problems of planing and semi planing hulls. The S Series suits boats between 17 to 50 feet. The system is fully automatic and significantly enhances performance, fuel economy, comfort and safety when accelerating and cornering. Thye have a built in GPS, 3D Gyro and 3D Accelerometer. 

A kit box includes all the parts needed to install a dynamic trim control system with one pair of fast acting interceptors. There are 4 different kit boxes, one for each length of interceptor model. The 4 different kits are the different interceptor lengths of 300mm, 450mm, 600mm and 750mm. The two most common kits by far are the 300mm and the 450mm and are the ones used on all our trailerboats including the large Yellowfin plate boats and the CruiseCrafts.

Each kit contains a pair on interceptors with 3mtrs cables on each, the control panel with a 7mtr cable and the distribution unit with a 4 mtr power cable. Dimensions of the control panel and the interceptors are in the pictures.